Semiconductor wafer under deep ultraviolet lithography exposure in a cleanroom fabrication facility

Deep UV lithography: how short-wavelength lasers enable advanced semiconductor chip manufacturing

Deep UV lithography uses excimer lasers at 365, 248, and 193 nm to pattern semiconductor wafers with nanometer precision. How it works, how it differs from EUV, and why chipmakers still need both.

ScienceWriter
Short Wavelength Sources Research Team

Chip feature sizes shrink because shorter-wavelength light resolves finer geometry. That is the whole physics of it, and it explains why the semiconductor industry spent decades pushing its exposure tools from visible-light lamps into near-UV, then into deep UV territory. Deep UV lithography uses excimer laser wavelengths from 365 down to 193 nanometers. It patterns the overwhelming majority of layers in every advanced chip made today, and it is not going away even as EUV handles the most demanding ones.

1. Three wavelengths define the DUV generations

According to ZEISS Semiconductor Manufacturing Technology, deep UV lithography uses wavelengths of 365, 248, and 193 nanometers to pattern semiconductor wafers with nanometer-level precision. Each wavelength corresponds to a generation: 365 nm i-line tools gave way to 248 nm KrF excimer systems, then to 193 nm ArF excimer scanners. Older wavelength tools were not simply retired; they remained in production for layers where their resolution was adequate and their cost per pass lower.

2. Excimer lasers are the light source for 248 nm and 193 nm systems

DUV systems at 248 nm and 193 nm do not use filtered lamp sources. The light comes from excimer lasers, pulsed gas-discharge devices that generate narrow-bandwidth ultraviolet output. ZEISS produces precision optics designed specifically for these excimer laser sources. The gas chemistry behind excimer emission is covered in the excimer lasers explainer on this site; for lithography purposes, the relevant output is a coherent, high-intensity UV pulse at a precisely controlled wavelength.

3. Immersion optics push 193 nm resolution below 40 nm

Resolution in a lithography system comes down to two numbers: wavelength and numerical aperture. The numerical aperture depends partly on the refractive index of whatever sits between the last lens element and the wafer surface. Air, with a refractive index of 1, sets a low ceiling on what is achievable. Water is higher.

ZEISS explains that swapping that air gap for ultrapure water deflects the light beam more strongly, pushing the numerical aperture up and resolution down. With 193 nm light and immersion techniques, the system resolves features below 40 nanometers. For context, that is well below 200 silicon atoms lined up end to end.

4. EUV uses 13.5 nm light and requires a full vacuum environment

Extreme ultraviolet lithography operates at a wavelength of 13.5 nanometers, roughly 15 times shorter than the 193 nm floor of DUV. At that wavelength, the physics change. According to Wikipedia, all matter absorbs EUV radiation, so the entire beam path, from source to wafer, must run inside a vacuum chamber. DUV systems work in ambient air.

The optics are also structurally different. DUV uses transmissive glass lenses, the same fundamental principle as a camera. ASML states that EUV requires all optical elements to be reflective mirrors built from alternating layers of molybdenum and silicon, because no transmissive material passes 13.5 nm light well enough to serve in a lens.

5. EUV takes the hardest layers; DUV does the rest

A finished chip at an advanced node requires dozens of distinct patterning steps, and not all of them need the same resolution. The transistor-level features at the bottom of the stack are the most demanding; interconnect layers higher up can live with somewhat coarser geometry. According to ASML, EUV handles the most intricate and complex foundation layers of advanced nodes while DUV systems print the remaining layers. In practice that usually means one or two layers per chip go through EUV, and everything else goes on DUV or older dry equipment.

6. DUV stays in production because it is cheaper to run

EUV scanners carry a substantially higher purchase and operating cost than DUV machines. Applying EUV to every layer of a chip would add cost with no resolution benefit for the layers that DUV handles adequately. ASML confirms that using older DUV machines for less complex layers is more cost-effective, since those machines are less expensive to purchase and maintain. EUV and DUV operate in parallel inside the same advanced fab, not as successive stages in a transition where DUV is phased out.

7. Multiple patterning extended DUV reach beyond its native resolution

Chipmakers have kept 193 nm immersion tools at the leading edge far longer than the physics of a single exposure would suggest possible. The technique is called multiple patterning: rather than resolving a fine feature in one pass, the system exposes two or more shifted patterns whose combined effect defines a geometry smaller than any single exposure could print. The strategy adds process steps and demands tight overlay control between passes, but it allowed DUV to serve at nodes that otherwise would have required EUV earlier.

8. China is printing near-frontier chips on older DUV tools through multipatterning

Export controls have restricted Chinese chipmakers from acquiring EUV scanners and certain newer DUV immersion machines. Analysis published by the American Enterprise Institute reports that chipmakers led by SMIC and Huawei are acquiring older-generation deep ultraviolet immersion tools and repurposing them to fabricate near-frontier chips. SMIC has already produced chips competitive with the US-led technological frontier and is actively developing a five-nanometer process node. The route is multipatterning at scale: running older DUV machines through additional patterning cycles to reach geometries those machines were not designed to hit in a single pass.

Near-frontier does not mean identical

A chip made on older DUV tools through multipatterning typically requires more process steps than the EUV equivalent, which adds cost and increases defect risk. At the most demanding nodes, DUV still cannot reach the density EUV can. For many commercial products, though, the gap is small enough that SMIC can compete on price and volume even if not on absolute transistor density.

Frequently asked questions

What wavelengths of light are used in deep UV lithography?

According to ZEISS Semiconductor Manufacturing Technology, deep UV lithography uses wavelengths of 365, 248, and 193 nanometers to pattern semiconductor wafers with nanometer-level precision.

What resolution can 193 nm DUV achieve with immersion optics?

According to ZEISS, lithography optics at 193 nm achieve resolutions of less than 40 nanometers when using immersion techniques, where water between the lens and wafer raises the numerical aperture beyond what air allows.

How does DUV differ from EUV lithography?

According to Wikipedia and ASML, EUV uses 13.5 nm light, requires vacuum, and uses reflective Mo/Si multilayer mirrors throughout its optical path. DUV operates at 193-365 nm in ambient air using transmissive glass optics fed by excimer lasers.

Which chip layers use EUV versus DUV?

According to ASML, EUV prints the most intricate foundation layers of advanced nodes. Only one or two of the demanding layers in a given chip require EUV; the remaining layers are printed on DUV or dry lithography systems.

How are Chinese chipmakers producing near-frontier chips with DUV tools?

According to the American Enterprise Institute, SMIC and Huawei are acquiring older-generation DUV immersion tools and running aggressive multipatterning processes to reach near-frontier geometries. SMIC has produced chips competitive with the US-led frontier and is developing a five-nanometer process node.